...
Blog

How To Install Curtain Rods?

Step by step guide showing how to install curtain rods

If you are tired of your weak or unattractive curtain rod, you can always switch it up. In this guide, we will discuss in detail how you can install a new curtain rod by yourself. Often, people don’t realize the importance of curtain rods and overlook how they can make or break the look of your curtains. Installing curtain rods is more than about screwing in the brackets on the wall. You have to consider a lot of other things. So, without further delay, let’s head right into how you can install curtain rods in your home with ease.

How To Install Curtain Rods? Step By Step Guide

1. Things You’ll Need

Tool / Material What You Need It For
Curtain Rod To hang the curtain
Brackets To support the curtain rod
Measuring Tape To measure the window’s width & height for the curtain rod
Finials To attach at the ends of the curtain rod
Allen Wrench To tighten screws on rods and brackets
Screws and expansion anchors To secure the rod on both hollow and concrete walls
Connectors (if you’re using a rod that is too long) To joining two curtain rods when the rod length is over 82 inches

Tools and materials needed for curtain rods installation

2. Measure For The Bracket Placement

The first step will be the measurement of your windows for the bracket placement. It is a bit tricky, but precision in this step goes a long way and can save you a lot of hassle later. The standard height placement for the bracket is 4 to 6 inches above the window frame. However, you can always adjust the height according to the dimensions of your room. If you notice that you can add some extra inches to the height of the curtain rod, it can be a good idea. Doing this will add the illusion of higher ceilings in the room.

You can also add 6-15 inches on all sides of the window frame. This will allow you to pull your curtains back all the way and expose the entire window for maximum natural light in the room. You can mark all these points so that you don’t forget later. You can also use a level to check if the measurements are even. Curtains that turn out to be lopsided can be very unflattering and also frustrating.

If you are installing a curtain rod that is too long, you will require connectors in the middle. How many connectors you will require depends on how long the curtain rod is. If the rod is over 82 inches in length and in two pieces, you will need one connector. However, if the rod is one single piece, you can skip the connector.

Curtain Rod Measurement Chart

Measurement Standard Size Why It Matters
Height above window 4–6 inches Suitable for standard 8 foot ceilings
Distance from crown molding 3–4 inches For rooms with higher ceilings to give the illusion of bigger windows
Extension for extra width Window width + 16-24 inches For maximum natural light by pulling back the curtains fully
Total rod width Rod length over 82 inches required 1 connector Only needed for single piece rods to support weight

3. Do A Mock Curtain Installation

Before you screw in your curtain brackets, do a mock installation to be on the safe side. You can hang the curtains on the rod and place the rod right where you marked the wall for installation. It will give you a correct idea of the height and width of the curtains that you will get. You can also decide whether you want the curtains grazing the floor or slightly touching the skirting. If the rod placement requires changes, you can make them accordingly without having to drill another set of holes and damage your walls.

4. Drill The Holes

Now, it is time to drill holes in your walls according to the measurements you took for the brackets. You can use a 6mm drill bit and then insert expansion screws in the drilled holes to ensure a sturdy base for the brackets. It is very important to choose the right screws for the walls according to their type. For solid walls, such as brick and concrete, you can use expansion screws. Whereas, for hollow walls, including metal, wood, and drywall, you can use ordinary screws.

 Screws & Drill Bits For Different Wall Types

Wall Type Screw / Anchor Drill Bit Size Note
Brick / Concrete (solid) Expansion screw with anchor 6mm masonry bit Sturdy support for heavy curtains
Drywall (hollow) No. 8 plastic wall anchor + panhead metal screw 1-1¼ inches 6mm Always use the anchor when you can’t find a stud
Wood / Stud Regular screws into pilot hole 2mm–3mm pilot hole The pilot hole prevents the wood from splitting
Metal Stud Regular screws or toggle bolts 6mm Use toggle bolts for heavy curtains

5. Install The Brackets

Now, you can install the brackets in the drilled holes. You can start by attaching the main part of the bracket to the base of the wall and tighten the screw until it is secure. The installation process is the same for all kinds of brackets. Whether you have a single curtain rod or a double curtain rod, it is important to consider the size of the double curtain rod and the distance between both rods. It affects how the curtain layers together and helps prevent the bunching of fabric.

6. Add The Rod & Curtains

Now, it is time to add the rod on the brackets and then hang the curtains. You can hang the curtains on the rod and then install it. Whether your curtains have grommets, rod pockets, tab tops, or back tabs, you can hang them on the rod first. It is easier than hanging the curtains while the rod is already on the bracket.

7. Finish With The Finials

Now, you can finish off by adding the finials of your choice. Whether you prefer something decorative or something simple is your choice. Once the finials are secure on either side, you are done. You can adjust the curtains to make them appear more luxurious and elegant.

8. Tadaa! You’re Done

You can now enjoy your handiwork and how the curtains add to the overall visual appeal of the interior.

How to Install Curtain Rods Step by Step Guide

Pro Tip For Rooms With Multiple Windows

If you are installing curtain rods on multiple windows with the same dimensions, you can work smart instead of doing everything from step one for each window. You can begin by cutting a cardboard square of 6 inches. Then, place the bracket against the cardboard and mark where the screw holes are located on the brackets. Now, every time you need to mark the point for holes, you can use that cardboard. Adjust the top of the square with the level line and mark the holes through the cardboard on the wall.

This will save you about 15 minutes on every window because you can simply line up the cardboard and mark the holes.

Frequently Asked Questions | FAQs

1. How high should I install the curtain rod?

The standard height to install the curtain rod is 4-6 inches above the window frame. If the room has a standard 8-foot ceiling, this height is ideal. However, for rooms with higher ceilings, you can install the rod even higher. A good rule of thumb is to keep a distance of 3-4 inches between the rod and the crown molding.

2. What should be the width of the curtain rod?

The width of curtain rods can be as much as you want. But the standard width for windows is 8-12 inches beyond either side of the window. If you want to determine how wide the rod should be before purchasing it, you can measure the width of the window and then add 16 to 24 inches to the total for an accurate measurement.

3. Which drill bit size is best for curtain rod installation?

The correct drill bit size for curtain rod installation is 6mm for standard plastic wall anchors. You can use a 2mm to 3mm drill bit if you are drilling a pilot hole. This will make sure that the hole doesn’t split the wood and provides a secure grip.

4. Can I hang the curtain rod without drilling?

Yes, some curtains are capable of hanging without drilling. If you are living in a rental property and don’t wanna drill any holes, you can use tension rods that are placed inside the window frame. They provide optimal support to hang the curtains without damaging the wall with drill holes.

5. Which screw do I use for curtain rod installation on drywall?

If you are installing a curtain rod on drywall, you can use a No. 8 plastic wall anchor and pair it with a matching panhead or a flathead sheet metal screw. The length for that should be 1 inch to 1¼ inches. These will work perfectly on hollow drywalls for curtain rod installation.

6. How long does it take to install a curtain rod?

The installation of curtain rods isn’t very time-consuming if you do it right the first time. If you gather all your tools and keep them ready, you can be done with the installation within an hour. If the room has multiple windows, you can create a cardboard template to expedite the process.

7. How do I install a curtain rod on a dry wall without hitting a stud?

If you want to install a curtain rod on drywall, make sure to use proper dry wall anchors. Doing this will ensure that the weight distribution on the rod is equal and the weight of the curtains can be supported optimally.

Tags: Blog
💬 Ask for Help
Seraphinite AcceleratorOptimized by Seraphinite Accelerator
Turns on site high speed to be attractive for people and search engines.